Installed two ceiling fans today: Hunter Casablanca Wisp 52" on back porch and Minka-Aire F844-DK Light Wave 52" in master bedroom. Used Arlington FB900 fan brace for porch installation and existing electrical box in bedroom. Wired fans with 14/3 Romex cable. Installed Lutron Maestro MACL-LFQ-WH fan/light dimmers for both. Balanced blades using Balco BTK-1 balancing kit. Secured mounting brackets with lag bolts. Tested functionality and airflow with Extech AN100 anemometer. Completed both installations in 4 hours, ensuring proper support and quiet operation.

Earlier today, I conducted an electrical safety inspection on a boat dock. Utilized a Fluke 1587 FC insulation multimeter to test GFCI outlets for proper function and trip times. Examined junction boxes for water ingress using a FLIR E6-XT thermal camera. Verified bonding of metal components with a Megger DET4TCR2 earth ground resistance tester. Inspected wiring insulation integrity and checked for proper gauge. Tested lighting fixtures for proper grounding. Ensured compliance with NFPA 303 standards for marinas and boatyards. Documented findings in a detailed report.

Recently, I installed a whole home surge protection system. First, I assessed the main electrical panel and selected a Square D Surge Protector. I shut off the main power and connected the surge protector to the panel, ensuring proper grounding. Used a Klein voltage tester to confirm safe installation. Tested the system to verify it will protect against voltage spikes. This installation safeguards all appliances and electronics from power surges, enhancing home safety and longevity of electrical devices.

This morning, I performed an electrical safety inspection on a home addition. Checked all new wiring for compliance with NEC standards, tested GFCI and AFCI breakers, and verified proper grounding. Used a Fluke multimeter to ensure correct voltage levels. Identified and corrected any potential hazards. The addition is now safe and up to code.

Conducted electrical inspection for new home addition. Verified grounding electrode system with two 8-foot copper ground rods interconnected per NEC 250.53(A)(2). Checked NM cable stapling at 4.5-foot intervals and appropriate box fill. Confirmed GFCI protection for all required outlets. Tested AFCI circuit breakers using integral test buttons. All electrical installations met current NEC requirements before dry walling.

Installed new outdoor lighting system following NEC Article 411 requirements for low voltage landscape lighting. Utilized 12V Kichler cable system with integrated direct burial PVC jackets. Trenched and ran cable from centralized 300W Class 2 transformer to landscape lighting locations per layout. Connected lights to cable system using gel-filled safety connectors. Terminated transformer secondary to lighting cable using suitcase connector, grounded unit. Installed rain-tight GFCI protected outlet and mounted transformer per listing. Adjusted lights, aimed landscaping illumination, buried cable to 6" depth minimum, restored planting.

I installed new GE Reveal LED recessed lighting fixtures in a residential kitchen, enhancing the area's brightness and energy efficiency. The process involved strategically planning the layout for optimal illumination, cutting precise openings in the ceiling, wiring each fixture into the home's electrical system, and securing the lights into place. I finalized the installation by testing each light for functionality, ensuring a modern, well-lit kitchen environment.

Installed whole-home surge protection in a Punta Gorda, FL residence. The Siemens FS140 model was professionally installed to safeguard all electrical circuits from power surges. This addition protects appliances and electronic devices, enhancing safety and minimizing potential damage from electrical fluctuations.

Installed recessed lights in multiple rooms throughout a Naples, FL home. Professionally placed in each room, the LED retrofit lights offer enhanced illumination and modern aesthetics. This upgrade ensures consistent lighting and ambiance, elevating the overall atmosphere and functionality of the residence.

Went out to a scheduled installation for a customer. They had asked us to install an outdoor GFCI outlet near the back of the house. Upon arrival, turned off the power before installing the outlet. Rewired the indoor outlet before testing. Everything is working as it should for the homeowner.

Installed a new outdoor ceiling fan for a customer. The homeowner wanted an updated fan in their patio space. Removed the old fan and installed the new customer provided one. Tested the fan to ensure it was in place and not wobbling before leaving.

Installed an outdoor ceiling fan for a residential customer. Customer provided the fan. Removed their old fan for them before installing the new one. Made sure the new fan ran correctly before leaving.

Customer saw our promotion for generator installations and asked for a consultation. Went to their home and discussed placement and the process of installation. Customer was interested. Scheduled a time to go back out.

Replace GFCI (fast-acting circuit breaker) to protect electrical shock in wet areas.

Installed Electric hot water heater ckt

Troubleshoot and repair electrical

Trouboeshoot and repair electrical short

Troubleshoot and repairnloss ofnpower to lights

Troubleahoot sprinkler system

Replaced all smoke detectors and repaired fans

Troubleshoot and repair electrical outlets

Replaced ceiling fan

Replaced electrical conduit and wires for AC

Troubleshoot and repair electrical

Replaced central vacuum